ATMEGA32L-8PJ【PDF 16/21 页】IC MCU AVR 32K 5V 8MHZ 40-DIP

收藏本站

您好，
买卖IC网欢迎您。
请登录
免费注册

买卖IC网

Sheet目录1905

12页 13页 14页 15页 [16页]17页 18页 19页 20页

2503QS–AVR–02/11

ATmega32(L)

The Atmel

AVR core combines a rich instruction set with 32 general purpose working regis-

ters. All the 32 registers are directly connected to the Arithmetic Logic Unit (ALU), allowing two

independent registers to be accessed in one single instruction executed in one clock cycle. The

resulting architecture is more code efficient while achieving throughputs up to ten times faster

than conventional CISC microcontrollers.

The ATmega32 provides the following features: 32Kbytes of In-System Programmable Flash

Program memory with Read-While-Write capabilities, 1024bytes EEPROM, 2Kbyte SRAM, 32

general purpose I/O lines, 32 general purpose working registers, a JTAG interface for Boundary-

scan, On-chip Debugging support and programming, three flexible Timer/Counters with com-

pare modes, Internal and External Interrupts, a serial programmable USART, a byte oriented

Two-wire Serial Interface, an 8-channel, 10-bit ADC with optional differential input stage with

programmable gain (TQFP package only), a programmable Watchdog Timer with Internal Oscil-

lator, an SPI serial port, and six software selectable power saving modes. The Idle mode stops

the CPU while allowing the USART, Two-wire interface, A/D Converter, SRAM, Timer/Counters,

SPI port, and interrupt system to continue functioning. The Power-down mode saves the register

contents but freezes the Oscillator, disabling all other chip functions until the next External Inter-

rupt or Hardware Reset. In Power-save mode, the Asynchronous Timer continues to run,

allowing the user to maintain a timer base while the rest of the device is sleeping. The ADC

Noise Reduction mode stops the CPU and all I/O modules except Asynchronous Timer and

ADC, to minimize switching noise during ADC conversions. In Standby mode, the crystal/reso-

nator Oscillator is running while the rest of the device is sleeping. This allows very fast start-up

combined with low-power consumption. In Extended Standby mode, both the main Oscillator

and the Asynchronous Timer continue to run.

The device is manufactured using Atmel’s high density nonvolatile memory technology. The On-

chip ISP Flash allows the program memory to be reprogrammed in-system through an SPI serial

interface, by a conventional nonvolatile memory programmer, or by an On-chip Boot program

running on the AVR core. The boot program can use any interface to download the application

program in the Application Flash memory. Software in the Boot Flash section will continue to run

while the Application Flash section is updated, providing true Read-While-Write operation. By

combining an 8-bit RISC CPU with In-System Self-Programmable Flash on a monolithic chip,

the Atmel ATmega32 is a powerful microcontroller that provides a highly-flexible and cost-effec-

tive solution to many embedded control applications.

The Atmel AVR ATmega32 is supported with a full suite of program and system development

tools including: C compilers, macro assemblers, program debugger/simulators, in-circuit emula-

tors, and evaluation kits.

Pin Descriptions

VCC

Digital supply voltage.

GND

Ground.

Port A (PA7..PA0)

Port A serves as the analog inputs to the A/D Converter.

Port A also serves as an 8-bit bi-directional I/O port, if the A/D Converter is not used. Port pins

can provide internal pull-up resistors (selected for each bit). The Port A output buffers have sym-

metrical drive characteristics with both high sink and source capability. When pins PA0 to PA7

are used as inputs and are externally pulled low, they will source current if the internal pull-up

resistors are activated. The Port A pins are tri-stated when a reset condition becomes active,

even if the clock is not running.

发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

*型号	*数量	厂商	批号	封装

添加更多采购

采购需求

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

我的联系方式